Hi,

This is my first post and I am just learning Ninjascript. I am working on a strategy that uses SbSRenko(5) as a primary Bar chart and SbSRenko(20) as a secondary.

In Initialize() I try to add the SbSRenko first and then the SbSRenko(20):

Add(PeriodType.Custom6,5);
Add(PeriodType.Custom6,20);

Then when I backtest I select SbSRenko(5) as a Data serie type. I got the "Custom6" by opening the file SbSRenkoChart.cs.


I would like to continue on something like:


// condition below should apply to my primary chart SbSRenko(5) and SbSRenko(20)

if (EMA(BarsArray[1], 5)[0] > EMA(BarsArray[1], 20)[0]) && (EMA(BarsArray[2], 5)[0] > EMA(BarsArray[2], 20)[0])
{
// condition below should apply to my primary chart SbSRenko(5)only
if (anaMACDBBLines(10, 12, 26, 1).BBMACDLine[0] >= anaMACDBBLines(10, 12, 26, 1).Upper[0]
{ EnterLong(DefaultQuantity, "");
}
}

Is that correct ?

Thanks.

philtrader 

Hi, This is my first post and I am just learning Ninjascript. I am working on a strategy that uses SbSRenko(5) as a primary Bar chart and SbSRenko(20) as a secondary. In Initialize() I try to add the SbSRenko first and then the SbSRenko(20): Add(PeriodType.Custom6,5); Add(PeriodType.Custom6,20); Then when I backtest I select SbSRenko(5) as a Data serie type. I got the "Custom6" by opening the file SbSRenkoChart.cs. I would like to continue on something like: // condition below should apply to my primary chart SbSRenko(5) and SbSRenko(20) if (EMA(BarsArray[1], 5)[0] > EMA(BarsArray[1], 20)[0]) && (EMA(BarsArray[2], 5)[0] > EMA(BarsArray[2], 20)[0]) { // condition below should apply to my primary chart SbSRenko(5)only if (anaMACDBBLines(10, 12, 26, 1).BBMACDLine[0] >= anaMACDBBLines(10, 12, 26, 1).Upper[0] { EnterLong(DefaultQuantity, ""); } } Is that correct ? Thanks.

Hi,

I am certainly not an expert yet with "Multi-timeframe" strategies but I can tell you the INIT you don't need the primary set in your chart type. Just add the 20 not the 5. 5 will be BarsInProgress==0 and 20 will then be BarsInProgress==1.

I am not sure your conditional statements are valid. You should probably use a construct more like:

If (BarsInProgress==0)
{// Put all sb=5 conditions,etc here
m_EMA5=EMA(Close,myperiod);
}

If (BarsInProgress==1)
{// Put all sb=20 conditions,etc here
m_EMA20=EMA(Close,myperiod);
}

Also note in your logic that if both bars close at the same time, BarsInProgress==0 will aways fire first. You should be able to use all the Open/Close/High/Low/Volume datasets and NT sets them to the appropriate data set. It uses BarsInProgress to tell you which data set they are currently point.

Thanks, it works now with your recommendation.

Hi can someone please post the sbs renko nt7 download I know it exists but cannot find it

Thanks

daytrader4 

Hi can someone please post the sbs renko nt7 download I know it exists but cannot find it Thanks

search use keyword sbsrenko
https://nexusfi.com/search/attachments/